West Jordan Foundation Pros
Driveway Lifting in Salt Lake City, UT
Driveway lifting in Salt Lake City with polyurethane foam injection: raise sunken slabs near the garage without full replacement, free estimates.
- 15+ Years local experience
- 500+ Projects completed
- Licensed & Insured
Serving West Jordan and nearby communities.
Why is my driveway sinking next to the garage after a few years? Driveway lifting raises a sunken concrete slab back to level using polyurethane foam injection through dime-sized drill holes, instead of tearing out and replacing the whole section. It's a separate job from structural foundation repair since nothing about the home's foundation is involved, just the slab outside it.
Utah's freeze-thaw cycle compacts the soil under a driveway unevenly over a few winters, and the slab near the garage approach often settles first because it's a common path for runoff. West Jordan Foundation Pros uses polyjacking (PolyLevel-style polyurethane foam) rather than old mudjacking slurry, since the lightweight foam won't add the extra weight that contributes to future sinking.
What's included
What's included with Driveway Lifting
Typically included: slab assessment, access hole drilling, foam injection at low points, hole patching and surface finish.
Optional: joint sealant resealing at expansion joints, surface sealer application after lift.
Customer prep: clear vehicles and items off the driveway, note any sprinkler lines running near the slab edge.
Want a clearer scope?
Get a Free EstimateHow it works
How our Driveway Lifting process works
Step 1Driveway Inspection
Sunken or sloped sections are identified for correction.
Step 2Access Drilling
Small holes are drilled at strategic points along the driveway.
Step 3Foam Injection
Expanding foam is pumped beneath the slab to raise it evenly.
Step 4Slope Correction
The surface is adjusted to restore proper drainage direction.
Step 5Hole Sealing
Drilled holes are patched to blend with the existing surface.
Step 6Surface Review
The driveway is inspected for even, stable elevation.
Materials
Materials and methods for Driveway Lifting
Polyurethane Foam
Provides lightweight lift without adding excess weight to the already-compacted soil beneath the driveway.
Concrete Patch Mix
Used to seal access holes after injection work so the surface stays flush.
Joint Sealant
Reseals expansion joints disturbed during the lifting process to keep water from re-entering.
Surface Sealer
Protects the driveway from moisture and future freeze-thaw cracking.
Leveling Equipment
Ensures accurate measurement during the lifting procedure, so one section doesn't overshoot level.
Bonding Primer
Improves patch adhesion to the original concrete surface around each drilled hole.
Questions on materials?
Get a Free EstimateTimeline
How long does a Driveway Lifting take?
Most driveway lifts complete in a single visit, with the slab drivable again shortly after.
- 01
Slab assessment
same day - 02
Access hole drilling and foam injection
1–3 hoursdepending on slab size
- 03
Elevation check and adjustment
same visit
- 04
Hole patching
same visit
- 05
Cure time before driving on it
a few hours
Need a schedule that fits?
Get a Free EstimateCodes & permits
Permits and codes for Driveway Lifting
Confirm with Salt Lake County or your city if the driveway approach touches a public sidewalk or curb cut.
| Typically needs a permit | Often no permit |
|---|---|
| Driveway work that also involves regrading near a property line or public right-of-way | Polyurethane foam injection and lifting with no structural modification |
| — | Access hole drilling and patching |
| — | Joint sealant and surface sealer application |
Need help with permits?
Get a Free EstimateDIY vs pro
DIY vs hiring a pro for Driveway Lifting
| DIY | Hire a pro |
|---|---|
| Filling small surface cracks with a basic concrete crack filler | Lifting a sunken slab evenly, which requires controlled injection pressure a DIY foam kit can't match |
| Sealing the driveway surface periodically to slow water intrusion | Matching slab height to adjoining sections without overshooting and cracking the concrete |
| — | Diagnosing whether the sinking is isolated or tied to a drainage problem that will cause it to sink again |
Not sure DIY vs pro?
Get a Free EstimateCost
What does a Driveway Lifting cost in Salt Lake City?
Pricing depends on slab size and how many sunken sections need injection, usually well under a full tear-out and replace.
| Project type | Typical range | What’s included |
|---|---|---|
| Single sunken section | $400-$800, | one low spot near a joint or garage approach. |
| Multi-section driveway lift | $800-$2,000, | several low points across the full driveway. |
| Full driveway releveling | $2,000-$4,000, | extensive sinking across most of the slab. |
These are typical local ballparks — final cost depends on scope, materials, and site conditions. A free estimate gives you an accurate, itemized number for your home.
Want a number for your home?
Get a Free EstimateNext step
Request a free estimate for an exact count of injection points needed.
When to call
When to call for Driveway Lifting
Call before the gap widens further or becomes a liability concern.
- A dip or low spot near the garage approach
- A trip edge where two driveway slabs meet at different heights
- Water pooling on the driveway after rain or snowmelt instead of draining away
- A slab that's sunk further than it did last year
Seeing warning signs?
Get a Free EstimateBefore & after
Before and after Driveway Lifting
Before 
After
FAQs
Driveway Lifting FAQs
Is foam concrete lifting cheaper than tearing out and replacing a driveway?
Yes, . Polyurethane foam injection typically runs a fraction of the cost of demolition and full slab replacement, since it works with the existing concrete instead of removing it.
Why is my driveway sinking next to the garage after a few years?
Soil under the garage approach often compacts unevenly after repeated freeze-thaw cycles, and runoff from the garage roof or downspouts can wash out fine soil particles beneath the slab, creating a void that eventually sinks.
How long does driveway lifting take?
Most driveway lifts complete in a few hours during a single visit, including drilling, injection, and patching. The slab is typically drivable again within a few hours of curing.
Do I need a permit for driveway lifting?
Usually not, since no structural modification happens. If the work extends to a public sidewalk or curb cut, check with the local jurisdiction first.
Can I use a DIY foam kit to lift my own driveway?
It's not recommended. Even injection pressure across the slab requires equipment and experience to avoid over-lifting one section and cracking the concrete.
Will the driveway sink again after lifting?
Foam injection fills the void causing the sink, and the lightweight foam doesn't add extra load that contributes to future settling. Ongoing drainage issues nearby should still be addressed to prevent a repeat.
What's the difference between foam injection and mudjacking?
Foam injection uses a lightweight expanding polyurethane through small holes, while older mudjacking pumps a heavier cement slurry through larger holes. The lighter foam puts less additional weight on soil that's already settling.
More services
Other Foundation Repair services
Foundation Repair
Foundation repair in Salt Lake City: crack injection, piering, and wall stabilization with free estimates.
Piering and Underpinning
Piering and underpinning in Salt Lake City: helical piers, push piers, and load transfer brackets to stop ongoing foundation settlement.
Wall Stabilization
Wall stabilization in Salt Lake City for bowing basement walls: steel anchors, carbon fiber straps, I-beams, and free estimates.
Ask about Driveway Lifting
Tell us about the project and how to reach you.